How to Install Pendant Light Without Junction Box
Let’s make this clear if you are searching how to install pendant light without junction box and looking for the exact ways of doing that, the straightforward answer is, “No, you can’t do that.” No matters what magic you use, you must have to set a junction box or an electrical box to prevent fires and any other electrical accidents. Whenever you are required to slice the wires for attaching it with the lighting fixtures, you must take the connection through the junction box. Otherwise, the chances of electrical accidents rise to the fullest.
So, you shouldn’t take the risk of installing the lighting fixtures without the junction box. But what will you do if there isn’t any junction box right where you have intended to install the lighting? Don’t worry; it doesn’t mean that you can’t install any lights there. If you have forgotten to install a junction box during your remodeling project or now to feel the necessity of this box, you can make the job done with a separate junction box. Instead of ripping the entire drywall, it will be the easiest way of getting the support of a junction box. Okay, now let’s have a look at some innovative ideas of installing the pendant lights.
How to Install Pendant Light Without Junction Box
The innovations of modern technology have used its magic wand at almost every place. At present, there are some premium lighting fixtures that don’t require any junction box because they have their own. This means you neither have to buy a separated junction box nor rip your drywall off. Isn’t that great? Some of these lightings are fluorescent fixtures, recessed lighting cans, and track lightings. If you are installing one of them, you can directly take the connection through the terminal box. Simply, make the connection and secure the electrical connection with screws.
When you are taking the cable into the fixture box, you should ensure its appropriate connection. Otherwise, it will cause some unwanted accidents. For this, you must secure it with clamps. You can also use the wire staples for securing the cables with the studs. If you can make a hole in your drywall, make sure to staple the wirings when you are feeding the cable through it. If you are attaching the fixture box to a stud, you must use the toggle bolts. It will be the most secure way of attachment. As such, you can avoid the accidental falling of the fixture box.
You Can Check It Out to Hang a Pendant Light in an Apartment
Using a Remodel Junction Box
The construction of a remodel junction box is simpler than the regular boxes. It is because they are designed to handle only one or two connections. But the conventional one can handle more, and that’s why they are bigger than the remodel junction boxes. This type of junction boxes uses an anchor for the attachment. That’s why it can be installed anywhere of your drywall. Just avoid the studs because you won’t be able to put an anchor into the studs.
However, let’s have a look at the procedure of attaching a remodel junction box with the drywall.
Step 1 – First of all, you have to place the back of the box on the wall and then mark the outline by using a pencil. After that, you have to measure the distance between the marks with a tape measure.
Step 2 – Now, follow the trace line and cut the shape by using a saw. Once you have completed that, remove the cutout from your drywall. Now, cut the metal studs to half of their length. The reason behind it is that you need to install the drywall once again.
Step 3 – At the back of the box, you will notice shelf-clamping holes, feed the electrical cable through those holes. After accomplishing that, position that box into the hole that you have cut earlier and then start pressing it until the bottom portion reaches the end of the drywall.
Step 4 – Place one of the screws on the front of the box in a location against the back of the plastic anchor on the drywall. Then twist the screw and move the box forward gently to hold the anchor. Continue this process with the other screw before tightening the screw entirely. Once you have done that, check both of the screws, then tighten all screws to seal the box absolutely. Now you can start adding wires to the box. To do this, gently push the wire into the hole in the electrical box. Make sure that the wire is not bent or kinked and also make sure that the wire is located on the back of the box.
If you have followed the above procedure, the box is now set in an accurate position with the wall. Finish the process with the installation of the crossbar. It usually comes with the light fixture so, check the package. Then connect the wires and secure the fixture appropriately. That’s it, you have made it. If you want to install a new outlet box or are planning to change the location of the existing one, this guide will help you. These steps are easy and safe to follow.
Frequently Asked Questions
Can I Install a Light Fixture Without a Junction Box?
Yes, you can install a light fixture without a junction box. This is because it doesn’t require electricity to operate.
However, the best thing to do is check with your local building department before installing the light fixture in case there are any rules or regulations that must be followed.
Are Junction Boxes Required?
Junction boxes are required for circuits that use both copper and aluminum conductors. In the United States, this includes wiring for homes and businesses that is installed in conduit or cable. There are many benefits of using junction boxes, such as:
• Easier installation of electrical systems by connecting wires together.
• Improved performance of electrical systems due to better insulation from outside noise and interference.
• Simplified repair by replacing a single damaged box instead of fixing an entire circuit board.
What Do You Do if You Don’t Have a Junction Box?
If you don’t have a junction box, then the first thing that you should do is call your local electrician. The next step would be to find an electrical outlet where there is no wire coming out of it and place the power cord in that area.
If none of these options work, then you can try using extension cords. If this doesn’t work either, then consider hiring an electrician or purchasing a new junction box for your home.
What’s the Purpose of a Junction Box?
A junction box is a device that is used to connect two cables or wires so that they can be joined in a circuit. It allows the power and data circuits to be connected and broken out.
The main function of a junction box is to protect the wires from being damaged when they are connected by means of making it possible for them to break apart again easily if there is an electrical short-circuit. The following are some more purposes of a junction box:
• It protects the wiring from fire, water, or corrosion.
• It provides extra security for people working on wiring work.
• It protects against theft and vandalism because it prevents outsiders from unplugging cables without detection.
Can You Ground an Outlet to the Box?
This is not possible. The outlet is connected to the box via a ground wire that comes from the electrical panel. The outlet does not have its ground wire, so it cannot be grounded in any way.
Conclusion
Hopefully, you have understood the above process and won’t have to ask anyone how to install pendant light without junction box anymore. If you are still confused, don’t hesitate to use the comment section below.
