How to Empty Dyson Cordless
Dyson cordless vacuums are a great option for anyone looking for an easy-to-use and lightweight vacuum. While they don’t have the same suction power as a standard upright vacuum, they are perfect for quick cleanups or small spaces. As a result, Dyson cordless vacuums are some of the most popular models on the market.
They are admired for their suction power and portability. However, like all vacuums, they need to be emptied occasionally. As a proud Dyson cordless vacuum owner, you may be wondering how to empty dyson cordless. We’ll show you how to do just that in this blog post. So keep reading for step-by-step instructions on emptying your Dyson cordless vacuum!
How to Empty Dyson Cordless: The Ten Quickest & Easiest Ways
1. Empty Clear Debris Bin
Remove the debris bin from the Dyson, pressing the release button at the side to release it. Empty dust/debris into the bin and pull out any fluff stuck to the inner wall.
2. Empty Full Bin
Turn the Dyson upside down and use one finger to push on the button at the side of the bin; this will open up a gap for you to empty it. Remove dust/debris from inside both chambers using a brush or your hand. Check the inner wall of each chamber for any fluff stuck to it.
3. Push a Plastic Bag Into Dyson
This is an old trash bag trick where you push a plastic bag into the opening at the top of the Dyson, allowing the internal parts around the cyclone unit to spin freely. This allows any stuck debris to fall into the bag.
4. Pull Out Plastic Drums
Turn the Dyson upside down and remove screws holding each plastic drum in place, then take them out one by one to empty any caught dust/debris free from around the cyclone unit. The amount of dirt you can see on the inner wall of the chambers will surprise you.
5. Clean Out Dust From Underneath
Turn your Dyson upside down and slowly rotate its base, checking behind to see if any dust has built up underneath it. Remove any stuck debris using a damp cloth or vacuum cleaner brush attachment.
6. Clean Out Pre-Motor Filter
Using a damp cloth, wipe the dust off of the pre-motor filter. Remove to wash in soapy water or replace with a new filter, careful not to damage it.
7. Remove All Filters Before Cleaning
Remove all the filters within your machine and clean them in soapy water. Allow them to dry before putting them back into place, paying special attention to the HEPA filter as it is susceptible.
8. Remove & Clean Out Dust From Hose
Remove the flexible hose from the main machine, remove any stuck debris around both ends, and remove the telescopic tube and clean its outer wall. Use a compressed air can to blast any dust from around the inlet valves and check the boxes for cracks or damage that may need repairing.
9. Turn Filter Grille
Using your fingers, turn the filter grille anti-clockwise; this will remove it, exposing the pre-motor filter. Clean any dust off the top and bottom of the filter with a damp cloth, then wash in soapy water or replace it with a new one.
10. Wash Mesh Filter
Using your fingers, push the mesh filter anti-clockwise to remove it, removing the filter underneath. Wash both filters in soapy water and allow them to dry before putting them back into place.
10 Effective Ways to Clean a Dyson Vacuum
1. Unplug Your Dyson
Before you start cleaning the inside of your Dyson vacuum, make sure that it is unplugged from any power source. The reason for this is simple. You do not want to get electrocuted, and Dyson did not want you to get electrocuted either.
2. Remove Dirt Cup
It is time to take out the dirt cup to clean out the inside of it. An easy release catch on most Dyson models will allow the dirt cup to be removed with ease.
3. Empty and Scrub the Dust Canister
Once the dirt cup has been emptied, you should clean it out with water and vinegar. The vinegar will help disinfect the container so that your vacuum smells clean. After this, you should dry the container out before placing it back into position on your cleaner.
4. Remove Wand/Hose
The next step is to remove anything that is attached to the cleaner. This will include taking out the wand, hose, or any tools that you have used with it in recent weeks/days. You should then clean everything thoroughly and allow them to dry before placing them back into position on your Dyson vacuum.
5. Detach Hoses
You will need to remove the hose from your Dyson before cleaning it. You should then carefully wash the hose out with water and allow it to dry before placing it back into position on your vacuum.
6. Remove and Wash the Filters
There are two filters that you need to pay careful attention to when maintaining your Dyson vacuum. The first is the pre-motor filter, and the second is the post-motor HEPA filter. These filters will require rinsing in water before being allowed to dry completely.
7. Rinse Exterior
It is a good idea to give your Dyson a rinse to get rid of any dirt, dust, or hair that has been allowed to build upon the Exterior. You can do this by using a hose with warm water, and it is essential not to use strong soap when rinsing off your Dyson vacuum cleaner.
8. Untangle the Brush Bar
You have one more thing to do before reassembling your Dyson vacuum. You should check the brush bar and remove any hair, thread, or anything else that has covered it so that you can place it back into position on your cleaner, ready for use.
9. Unclog the Hose
Before you put everything back in place, please look at the hose and remove any blockages that may have occurred while you were cleaning it.
10. Wipe Down the Vacuum
Finally, it would help if you wiped down the Exterior of your Dyson vacuum with a soft cloth to remove any dust or debris that may be present on it. If you have any stubborn dirt, you can spray it with a solution of water and vinegar.
Some Tips and Suggestions
1. To avoid some of the suction loss prevalent with most cordless stick vacuums, do not move away from a pile of dirt as you continue to vacuum.
2. The more holes in the dirt-bin compartment (e.g., missing hair or carpet fibers), the harder it will be to clean out at the end of a cleaning session.
3. Some dirt will be visible on the outside of the dirt-bin compartment at the end of a cleaning session.
4. It is advisable not to wait until there is insufficient suction before emptying the bin and filter, as this will cause more stress on the motor and reduce its life expectancy.
5. To avoid having the batteries too low for continued use, do not wait until your vacuum emits a low battery warning light before emptying its dirt bin and filter. This will cause additional stress on the batteries both during and after the cleaning session.
6. While this issue may seem like a minor nuisance, an empty dirt-bin is less likely to be pushed around on hard surfaces by the beater bar brush assembly, which can increase the risk of it being damaged if it comes into contact with side-wall trim or baseboard molding.
7. Having your cordless stick vacuum in use with a full dirt-bin and filter will not damage your batteries. It is merely inconvenient because of the reduced suction capability and the fact that you will need to empty them more frequently.
Frequently Asked Questions
Q: How Do I Empty a Dyson Cordless?
A: There are several different Dyson cordless models. Each model follows a slightly different process for emptying the bin. For example, the Dyson Slim vacuum cleaner includes a separate bin release button under the handle. The user presses this button to open the lid of the garbage disposal unit at the back of the machine. Once opened, the user can easily remove the full bin and replace it with an empty one.
Dyson Animal vacuum cleaner includes a button on the top of the machine that opens up the disposal unit at the bottom of the machine when pressed. Once opened, press down on one side of the waste bin to release it from the disposal unit and empty out its contents. If you want to more, consider reading this full blog post on how to empty dyson cordless.
Q: How Can I Empty a Dyson Bagless?
A: Dyson vacuum cleaner that has no bags requires the user to remove the dust from the filter found inside the machine. To do this, firstly, open up the bin doors by releasing their buttons and sliding them down. Then press down on the handle above where your hand will be. This will pop off the filter cover and allow you to empty the machine’s bin contents by pressing on it or sliding it out of its slot.
Conclusion
The Dyson cordless vacuum cleaner is one of the best-selling handheld vacuums on the market. It was designed to be lightweight and versatile, making it easy for you to clean any room in your house without having to unplug cords or lug around a heavy machine. With so many great features that make this vacuum stand out from other models, there are also some things you can do with it that will help keep it running smoothly for years!
It would help if you emptied your Dyson cordless at least once every six months by removing all dirt and dust collected inside by opening the bottom hatch. To get rid of stubborn pet hair stuck in hard-to-reach places like stairs or upholstery, run over these areas with the vacuum to build up a static charge, then use narrow strips of packing tape to pull hair from deep within crevices. We hope this blog post on how to empty dyson cordless has been helpful. If you have any questions or want to know more, then feel free to comment below!
