How to Remove Back Window From Truck
It’s not always easy to remove the back window from a truck, but it can be done with some elbow grease and patience. There are many different ways you could go about doing this task. In this blog post, we will talk about how to remove the back window from truck. So if you have no idea about it, then consider reading the full blog post.
Supplies You’ll Need
Below is the list of supplies that you need to remove the rear window from the truck:
1.Goggles:
The only thing you need to do during this procedure is breaking a lot of glass, so it may sound stupid but wear safety glasses . Glass shards can go anywhere, including your face and eyes. You don’t want that to happen.
2.Towels:
You will be removing the glass, and you don’t want to do it with bare hands, so get yourself two towels. They will absorb the broken glass.
3.Glass cutting tool:
You need something strong enough to cut the glass, I used a cold chisel, but any hammer or anything with a flat end will do the work.
4.Ladder:
A regular step ladder is enough to remove the rear window from the truck, but a tall one will make your job easier. You can’t be on the ground and prying out the glass at the same time as it’s too dangerous. So using a taller ladder not only makes it easier but a lot safer as well.
5.Gloves:
You don’t want to get cut by the glass, so wear gloves. I didn’t take this precaution and now have three small cuts on my palm. Even with the goggles, it was still missed a few times. If you don’t want to regret it later when you see the blood, then wear gloves.
6.Bucket:
You need to put all of the broken glass in one place to not litter your garage floor or driveway.
7.Towel paper:
If you are not using polyethylene garbage bags, then a few paper towels will also work.
Steps on How To Remove Back Window From Truck
Step 1:
First of all, turn off the engine. Then with the help of a friend, open up the back door to remove it. If you don’t have any help, then use something that can prop it up like wood so that the door opens freely.
Step 2:
The next step is to pry out the trim pieces on both sides of the glass. If it’s a metal panel, you will need to use the glass cutting tool to cut through them. They are usually secured using screws or pop rivets, so unscrew those and remove that piece of trim.
Step 3:
At this point, you should be able to see how the back window is attached to the truck and what kind of screws are holding it. The back glass has two metal bars that go down to the bottom corners, so use the chisel or hammer to remove those screws.
Step 4:
Now it’s time for some hard labor, but you will be rewarded shortly because you can now remove your back window from the truck. All you have to do is grab the panel and gently pull it out. If it does not come out as easy, you will probably notice that some screws are holding them in place, so remove those with the help of a screwdriver or drill.
Step 5:
You removed the back glass from the truck, so now it’s time to dispose of all the broken rear glass. You can either use garbage bags or polyethylene garbage bags, but I prefer the former because they are reusable and cheap. So just place them on a table and pour in all of the broken pieces.
Step 6:
After that, sweep the garage floor or driveway if there are any small shard pieces of glass and dispose of them in a garbage bag. That’s it! You just learned how to remove back window from truck.
8 Things To Consider When Removing Back Window From Truck
1. Safety:
It is always best to remove ANY glass from the vehicle if there’s any doubt on the condition of your windshield or back window. Even a pebble can create great damage when operating at highway speed.
2. Wind Noise:
Generally speaking, every time you add another layer of sound deadening (such as taping the window back in), you add additional thickness to your power window. This may increase overall wind noise and decrease how well you hear what’s going on around you while driving.
3. Weight Affect:
Adding sound-deadening material or a new power window may affect your truck’s center of gravity, which can also result in increased fuel costs, poor handling, and reduced towing performance.
4. Cost:
Replacement windows can be had for as little as $100, but if you’re not careful, the price can really escalate quickly depending on size, quality, and back window curvature. You may also need increased hardware to install a new glass windows, such as additional mounting brackets or other attachments that may or may not come with the new window.
5. Appearance:
A larger back window has a more streamlined appearance than a smaller one and will have less of an impact on your truck’s overall look. A beautifully finished wood frame will add warmth to your interior and complement almost any existing upholstery or trim color inside your cab. Wood is also known to be much stronger than aluminum or fiberglass, two other materials that window manufacturers use to fabricate replacement windows.
6. Finish:
Aluminum and fiberglass are flexible materials that can lead to a more difficult time achieving a perfect fit for your back window frame in the truck cab. On the other hand, wood is firm but very pliable, making it easier to achieve an excellent fit.
7. Durability:
Wood will retain its finish and color longer than either aluminum or fiberglass due to its pliability. Aluminum and fiberglass, however, are more resistant to corrosion from road defroster and saltwater, as well as other environmental factors that can shorten the life of your rear window defroster over time. So ultimately, wood lasts longer than aluminum and fiberglass.
7. Noise:
Because of the less dense nature of wood, a window frame made from this material will allow more noise into your truck cab than a window frame made from either aluminum or fiberglass. But adding additional layers to the glass may dramatically increase wind noise when you’re driving, so be careful. However, if you’re willing to sacrifice some noise leak for beautiful wood trim that will complement your truck’s finish, a wood rear window glass is a way to go!
8. Heat Retention:
Wood conducts heat much better than aluminum or fiberglass and may negatively affect how warm or cool your cab feels, especially when not in use! If you live in an area where a lot of people let their trucks sit in the sun without shade, then you’ll need to consider this factor.
Tips To Remove Back Window From Truck Without Breaking It
- Open the door, then remove the plastic cover of the back window film firstly.
- Un-clip the screws on the rubber seal of the truck cab.
- Remove screws from the metal holder and take it off.
- Use a screwdriver to turn over two clips at both ends of the truck bed wall, then you can take off the window.
- Remove the screw on both sides of the truck bed wall and carefully take off the metal holder.
- Then you can remove the damaged window or replace a new one easily.
What Should You Know Before You Start Remove Back Window From Truck?
- You’d better not remove the rear cab window if it is still in good condition, because you need a high cost to replace or fix it.
- Make sure you have prepared any special tool for removing the window before you start this job; otherwise, it will be very difficult to take off the broken glass and seal strips from the truck body.
- Clean the window and prepare any glass glue before you start this project because it is very easy to be messy during the process of removing the windows.
- If you can remove the window for replacement, you’d better check if there is any damage to the truck body or the glass when removing a dented window because it may cause leak water on rainy days.
- Have someone help you so that this job would be done much easier and faster.
How to Measure Window Size?
Before you do anything else, it is important to measure the size of the potential new window. Measure from top corner post on one side to bottom corner post on the other side. If there are any obstructions in your way (wires, handles, etc.), you should make sure that they will not hinder the re-installation process later.
If you are using a custom-sized window, the measurements will probably need to be exact. If you do not have exact measurements and will be using a replacement window from an after-market supplier, make sure that there is at least a 1/4″ gap between the frame and your new pane of glass.
Why Would You Remove the Back Window of a Truck?
There are a number of reasons why you would want to have rear window replacement from your truck. This includes making it easier to access items and equipment from a cargo bed. It can also create more space in the vehicle, allowing for more comfortable transporting of passengers.
You’ll need some basic hand tools to accomplish this task. The amount of time needed will depend on the type of window gasket that you have installed in your truck. If you have roll-down or sliding windows, removal may be quicker than for other types of windows, such as double-hung or casement window if they are present.
Frequently Asked Questions
Q: When Should You Replace the Back Window?
A: While removing the backside window is an easy way to make it easier to access cargo that’s stored in your truck bed, it may not be the best option. If you frequently need to reach items from the back of your truck, a center below window replacement for your tailgate might make more sense. This will give you much more space to place items in the bed without having to remove anything.
If your back glass is cracked or damaged and the weather stripping around it is also deteriorated, this can create leaks that will expose your cargo to moisture and put them at risk of damage. A full replacement window can stop these problems by creating a barrier between your cargo and the outside environment. Other common causes of tailgate glass damage include vandalism or accident-related damage.
Q: How to Remove Tint From Back Window?
A: When you think about a pickup truck, what comes to mind first are the great open roads, good weather, and trucks. Forget about sealed windows with air conditioning or a radio that is running on batteries. In fact, it’s been like this for years until recently in America, and it was hard to find an SUV without tinted windows.
If you want to keep things simple, you can install old-fashioned window curtains. That’s a cheaper option than spending money on tint removal services. You can remove the back window from your pickup truck and install a curtain yourself.
Q: How Much Does It Cost to Install a Back Sliding Window?
A: The cost of replacing your damaged truck window is influenced by a number of factors. For example, if you have to remove the door panels and the back glass itself, you are likely to spend more money than you would just to replace them.
Costs can be higher if your truck has something unusual like a backslider or double-hung window. They can be expensive to replace, especially if they are custom windows that you cannot find online or at your local glass shop.
Conclusion
It’s not always easy to remove the back window of your truck, especially when it is broken. Luckily, This post has given you all the information you need in order to successfully complete this task yourself.
Now that you know how to remove back window from truck, we hope this article helped. If you have any questions or confusion, or if something isn’t working for you as expected, please contact us!
