How to Remove Water Restrictor From Hansgrohe Raindance Shower Head
You may need to remove the water restrictor to get the most out of your Hansgrohe Raindance Shower Head. If your shower head is not producing a strong enough stream or has started to drip, it’s likely because there is a small metal ball in a place that restricts the flow. All you have to do is unscrew and remove this little ball from inside the showerhead! In this blog post, we will discuss how to remove the water restrictors from the Hansgrohe Raindance shower head.
Many people find that removing the water restrictor can improve their experience with a shower. You’ll also see why some people prefer to keep it on and what benefits there are for both sides of the debate. Read on for all the details about removing your water restrictor and other information about these products!
8 Reasons Why Remove Water Restrictor From Hansgrohe Raindance Shower Head:
If you want to remove the water restrictor from your Hansgrohe Raindance Shower Head so it can produce a full, strong spray of water while saving on the amount of hot water used, here are eight reasons why.
1. Reduce the chances of getting burned if you have children or grandchildren who like to explore by turning on the hot water and letting it run. The water restrictor limits the amount of hot water that can flow out of your shower head, so even at full throttle, and you’re getting less than a full blast of scalding hot water. On the other hand, if you remove the water restrictor, you get a full shot of hot water.
2. You can use less hot water. The exact amount of hot water is available. Still, since it’s not restricted anymore, because the Hansgrohe showerhead doesn’t limit how much comes out, you don’t need to turn on your hot water as high to get a satisfying shower.
3. Reduce your heating costs. There’s no sense in heating water that you’re never going to use, so if you remove the water restrictor from your Hansgrohe Raindance Shower Head, you can turn down or even off your water heater and save some money on heating costs.
4. If you want to get cleaner hair and skin after showering, turn off your water heater for a while and take shorter showers. When you remove the water restrictor from your Hansgrohe shower head, it’ll spray out more warm but not scalding water so you can enjoy ten minutes of lusciously warm water to get cleaner hair and skin while still saving on your heating bill.
5. If you have hard water, you’ll get less calcium build-up if you remove the Restrictor from your Hansgrohe shower head so it can spray more hot water at full force. Also, cleaning calcium deposits off of fixtures in your bathroom is much easier if you remove the water restrictor from your Hansgrohe showerhead. Hence, it shoots out a stream of water instead of a trickle.
6. Use less detergent when doing laundry. If you have hard water, taking shorter showers with an unrestricted Hansgrohe Raindance Shower Head will reduce the amount of calcium in your clothing because you’ll have less build-up.
7. If you have a dishwasher, an unrestricted Hansgrohe Raindance Shower Head will reduce water spots because it shoots out more water to clean your dishes and save on the amount of detergent you use.
8. If you remove the water restrictor from your Hansgrohe showerhead, you can get a more consistent water pressure throughout your shower. When the Hansgrohe showerhead is restricted, it creates a pulsating effect.
10 Ways on How to Remove Water Restrictors From Hansgrohe Raindance Shower Head:
Below we have discussed the ten ways how to remove the water restrictors from the Hansgrohe Raindance shower head. Be sure to check this guide for removing water restrictors from the showerhead.
1. Disconnect the Shower Head:
Before removing the water restrictor, you will want to disconnect your shower head from its arm. For example, if you are facing a wall, you should simply pull the shower arm forward and disconnect it from behind.
2. Remove Restrictor:
There will be a screw or bolt at the base of your shower arm. Remove this and remove the Restrictor inside. Some people find it easier to un-thread their shower arm entirely before doing this, but it is unnecessary.
3. Add Silicone Sealant:
If your shower arm is now loose, you will want to add some silicone sealant before screwing it back into place. This will ensure that the water restrictor cannot fall down the shower pipe again. This step might not be necessary if your shower head is not connected via a wall or ceiling.
4. Check for Restriction:
If you have a pressure-balance shower valve or another type of low-flow showerhead, you may need to replace the Restrictor. If your previous shower head was not restricted and this replacement restricts water flow too much, it may be necessary to remove more from the Restrictor.
Please do this by re-opening the end of the Restrictor, releasing more of its contents, and then closing the end again. Test your shower head for adequate (non-restricted) water flow.
5. Screw-on Shower Head:
After adding a silicone sealant, screw your shower head back into place using the appropriate washer. Use plumbers tape if necessary, tightening it slowly and carefully to avoid breakage. Finally, turn on the water supply to ensure that there are no leaks.
6. Test Shower Head:
After your shower head is successfully reattached, you should leave it on the faucet for about an hour to check for leakage. If there are no leaks after this time, you will be ready to turn on your water and try out your newly un-restricted shower head!
7. Different Size Restrictors:
Many shower heads will come with a similar, pre-installed water restrictor. However, suppose your shower head is restricted, and you have already unscrewed the water restrictor but cannot remove enough from it to adequately un-restrict your shower head.
In that case, there are replacements available for purchase online. This may be necessary under some circumstances.
8. Finding Replacement:
Replacement water restrictors can be purchased at your local hardware store. However, if you cannot find the exact size that works with your shower head, you will need to buy a pipe threading kit to make it larger or smaller for a perfect fit.
9. Using a Drill:
A drill and steel (or ceramic) bur will allow you to manually grind down the Restrictor in your shower head so that it does not restrict water flow. While this method may damage your shower head, it works well when no other replacement is available for purchase online.
10. Stripping the Restrictor:
While this is not ideal to un-restrict your shower head, it sometimes does work. You will need a pipe threading kit and tape to strip your Restrictor. Next, take apart the Restrictor carefully, keeping track of all pieces. Once it is stripped down to replace any components, use the appropriate sizing kit to make it larger or smaller. And then, use plumbers tape to reassemble your shower head.
Things to Consider Before Removing Water Restrictor From Hansgrohe Raindance Shower Head:
Here are some things to consider on removing the water restrictor from the Hansgrohe Raindance shower head.
1. Removing the water restrictor from a showerhead can increase your maximum allowed water flow by 30%. However, it is possible to break your shower if you remove restrictors from it.
2. If you want more pressure, there are other ways of achieving this. For example, replacing old or broken pipes and plumbing with new ones can increase pressure without removing the Restrictor.
3. Removing water restrictors will only work if your shower has a restrictor in it. Some newer models may not have them anymore, so this method is not good for you.
4. If you are unsure whether your shower has a water restrictor, check with the manufacturer or owner’s manual. It may require a screwdriver and pliers to remove.
5. This method will make your showerhead’s gasket (seal) less effective. You were eventually leading to leaks around the head or at the joint due to wear and tear.
6. This method will also void any warranty on your showerhead or home plumbing that you may have, so use this knowledge at your own risk.
7. Hansgrohe water restrictors are made from a soft rubber-like plastic that can be melted with heat from a gas stove burner or oven burner.
Advantages of Removing Water Restrictor From Hansgrohe Raindance Shower Head:
1. Do not have to replace an already installed shower head with a low flow version and risk not having enough force for adequate cleansing
2. Showerhead may be able to reach the full water pressure the manufacturer intended
3. Showerhead will spray at the original diameter without placing a hand in front of it or using a shallow flow setting (causing you to use much more hot water than necessary)
4. Have peace of mind knowing both your wallet and environment are getting the full benefit of the water usage.
5. More satisfying shower experience when using full water pressure instead of using low flow version or not being able to feel the water
Disadvantages of Removing Water Restrictor From Hansgrohe Raindance Shower Head:
1. Water usage might increase but still much less than other showers present in your area, so it will decrease over time
2. Cannot use a very low flow setting without placing a hand in front of it or restricting water with your thumb
3. May notice an increase in noise at high-pressure settings with restricted shower head
4. Risk of personal injury if using full force water while not being aware of surroundings, especially in places where the floor is slippery
5. If you have any health conditions that high-pressure water may affect you, you should not attempt this.
When To Keep Your Water Restrictor In Place?
If you have low water pressure from your city’s municipal water source, don’t remove the water restrictor from your Hansgrohe Raindance showerhead. It will only make the problem worse for you and your household.
Likewise, if you have a water softener installed in your home, don’t remove the water restrictor from your Hansgrohe Raindance showerhead. The presence of excess minerals in hard water can clog up an entire shower head, forcing air into the water flow.
Don’t remove the water restrictor from your Hansgrohe Raindance showerhead if you have a well that provides your home with its municipal water supply. If this is not enough reason to keep it in place, consider that most wells see twenty-foot drawdowns and deeper daily.
This means that they are subjected to dirtier water than a city’s municipal source. If you want more information on removing the water restrictor from the Hansgrohe Raindance shower head, we suggest reading this full blog post.
Can I Remove Shower Flow Restrictor?
Hansgrohe shower heads are famous for their pressure. This is because they offer steady water flow, which makes cleaning or bathing enjoyable and easy. However, some of the Hansgrohe Shower Heads come with Flow Controls that limit the pressure by restricting water flow.
Usually, it is better to leave this feature alone because you do not want your shower head to have a high water bill. But, on the other hand, you want to have a nice, enjoyable shower free from insufficient pressure or being blocked by these flow regulators.
How Do You Remove a Shower Head Limiter?
The water limiter is a device that restricts the flow rate of a showerhead. Limiting or restricting the flow rate can help reduce your water usage and conserve water. The Hansgrohe showerhead contains a built-in water regulator, which must be removed before using it as a handheld unit. The shower’s spray pattern will be much broader with the limiter.
Remove the water limiter from a Hansgrohe Raindance showerhead by unscrewing the small plastic bushing which holds it in place over the swivel ball. You can also use a pair of needle-nose pliers to remove the plastic bushing from your shower head. This will allow you to detach the showerhead from its bracket and use it as a handheld unit.
Conclusion
The Hansgrohe Raindance shower head is an excellent choice for those looking to upgrade their bathroom. It provides the right amount of pressure and has an easy-to-clean water restrictor that can be removed with just one tool! The good news is that removing a water restrictor from the Hansgrohe Raindance showerhead can be accomplished relatively easily.
We recommend using an adjustable wrench to remove it, as this tool will allow you to secure the piece and avoid damaging your plumbing system in any way. If there are no screws on either side of the device, use pliers instead! We hope this blog has helped explain how to remove the water restrictor from the Hansgrohe Raindance shower head and wish you all the best!
Angela Ervin
Angela is the executive editor of DIY quickly. She began her career as an interior designer before applying her strategic and creative passion to lifestyle and home. She has close to 15 years of experience in creative writing and online content strategy for housekeeping, home decorations as well as other niche efforts. She loves her job and has the privilege of working with an extraordinary team. She lives with her husband, two sons, and daughter in Petersburg. When she's not busy working she spent time with her family.
