How to Get Oil Filter Off Without Wrench
If you ever find yourself in a position where you need to change the oil on your car but have no wrench, some things can help. One of these uses a pair of pliers with a rubber band wrapped around them. Another is using a large crescent wrench or even an adjustable spanner, which can do the job just as well without buying one from the store.
This blog post will show you how to get oil filter off without wrench! One of the most common remedies for an engine making noise is to replace the oil filter. If you’re not comfortable doing this job yourself, don’t worry.
It’s a relatively easy task as long as you have the right tools. You’ll need a few simple items, like a socket and ratchet set, and you’ll be good to go. So, read on for instructions on removing the old filter and installing a new one.
10 Ways on How to Get Oil Filter Off Without Wrench:
1. Use a Socket:
A socket wrench is a tool that can be used to remove an oil filter. The socket should be the same size as the oil filter’s base. This allows the user to grip the filter tightly and extract it from its location.
2. Use a Strap Wrench:
A strap wrench is a tool that can be used to remove an oil filter. The strap should fit over the circumference of the filter and tighten as it is turned. This allows for a tight grip on the filter, removing it from its location.
3. Use a Hammer and Drift Pin:
A hammer and nail can be used to remove an oil filter. A nail is driven through the center of the filter’s base, which will allow it to spin freely upon contact with the hammer. The spinning motion combined with the force created by the hammer loosens the filter from its location.
4. Use a Screwdriver:
A screwdriver can be used to remove an oil filter. A flat head screwdriver is placed under the edge of an oil filter’s base, which aids in loosening it. The upwards force created by the screwdriver allows for removing any oil filter.
5. Use a Rubber Strap Wrench:
A filter wrench can be used to remove an oil filter. The wrench has two arms that grip the circumference of the filter. This allows for a tight grip on the filter, removing it from its location. When an oil filter is removed, the oil that was inside of it can spill out. It is important to have a pan or other container to catch this oil so that it does not make a mess.
6. Use a Pipe:
A pipe can be used to remove an oil filter. The pipe should be the same size as the oil filter’s base. This allows the user to grip the filter tightly and extract it from its location.
7. Use a Crescent Wrench:
A Crescent wrench can be used to remove an oil filter. The wrench has two arms that grip the circumference of the filter. This allows for a tight grip on the filter, removing it from its location.
8. Use a Bottle Opener:
A bottle opener can be used to remove an oil filter. The teeth on a bottle opener can grip the base of an oil filter tightly so that it may be removed from its location.
9. Use a Belt:
A belt can be used to remove an oil filter. A belt is looped over the circumference of an oil filter and tightened as it is pulled up. This allows for a tight grip on the oil filter, removing it from its location.
10. Use a Chisel:
A chisel can be used to remove an oil filter. The chisel is inserted into the seam of an oil filter’s base and tapped with a hammer. This loosens the filter from its location. Whichever method is chosen, be sure to be cautious when removing the oil filter. The old filter can be pretty dirty and should be disposed of properly.
What Tool and Supplies You’ll Need:
- Breaker bar or long socket wrench
- 10-15 inch crowbar or large flat head screwdriver
- Channel locks
- Rubber mallet
Instructions: How to Get Oil Filter Off Without Wrench
Step 1:
Begin by spraying the oil filter with a lubricant such as WD-40 or PB Blaster. Allow the lubricant to sit on the filter for a few minutes.
Step 2:
Next, use the breaker bar or long socket wrench to remove the oil filter. If the filter is stubborn, you can try using a crowbar or large flat head screwdriver to pry it off instead.
Step 3:
If the filter is still difficult to remove, use channel locks to hold the filter in place while you pry it off. You can also use a rubber mallet to tap against the end of the crowbar for extra leverage (be sure to wrap the crowbar with tape first).
Step 4:
Once you’ve removed the old oil filter, clean up any remaining lubricant with soap and water. Clean up the oil filter mounting surface with an engine degreaser.
Step 5:
After letting the engine degreaser sit on the oil filter mounting surface for a few minutes, wipe it off with a towel.
Step 6:
Use an oil filter wrench to hold the new oil filter in place while you hand-tighten it into place. Make sure it’s not over-tightened.
Step 7:
Reinstall the drain plug and fill your engine with fresh oil.
That’s all there is to it! You can remove an oil filter without a wrench by following these simple steps. If you have any questions or run into any problems, don’t hesitate to ask for help. Your local auto parts store should be able to offer assistance as well.
Some Tips to Getting Oil Filter Off:
- Try using a socket wrench or an oil filter wrench to get the filter off.
- If you have difficulty getting the filter off, try using penetrating oil.
- If you still cannot get the filter off, try heating it with a hairdryer.
- If you need to replace your oil, consider replacing your oil filter as well since it is probably full of grime and residue from its use.
- Always dispose of your oil filter properly by recycling it or taking it to a hazardous waste disposal site.
Note: By following these tips, you should be able to get your oil filter off without using a wrench. If you have any trouble, be sure to consult your vehicle’s owner’s manual for more specific instructions.
Common Mistakes to Avoid When Getting Oil Filter Off:
1. Not Using the Right Tools:
Many people try to get the oil filter off without any means, leading to a lot of frustration and damage. Instead, ensure you have the right tools for the job, such as an oil filter wrench.
2. Applying too Much Pressure:
When using the wrench, don’t put too much pressure on it, or you could damage the filter or the engine. Instead, apply even pressure and turn the wrench slowly to avoid problems.
3. Not Cleaning the Area:
Before you start, make sure you clean the area around the oil filter so that any dirt or debris doesn’t get into the engine. This will help keep your car running smoothly.
4. Trying to Reuse the Oil Filter:
Never reuse an old oil filter on your car because it could have already lost some of its filtering properties, which means dirt and debris could get into the engine, causing damage. Instead, always use a new oil filter when changing your oil.
5. Not Tightening the Filter Enough:
Make sure you pull the filter correctly once it’s on to avoid any leaks. If the filter isn’t tight enough, it could come loose and cause more problems.
Conclusion:
If you’re in a pinch and need to get your oil filter off without the right tools, here are some tips that might help. First, try letting it soak overnight. Next, if this doesn’t work, then take a look at how tight the bolt is on top of the filter housing by unscrewing it just enough so there’s no pressure from below.
Use something like an old credit card or other thin objects to pry up slightly while also using both hands for leverage against the bottom of the filter housing. Once loosened, use one hand to hold down firmly around where you’ve been working with your fingers spread out over as much area as possible, and use your free hand to twist counterclockwise until it breaks loose.
We hope this blog post on how to get oil filter off without wrench has been helpful. Let us know your thoughts in the comments below!
