How to Remove Brake Light Switch Trailblazer
The brake light switch is a small device that mounts to the brake pedal arm and sends an electrical signal to the vehicle’s braking system.
Brake light switches can be difficult to remove from vehicles, as they are often bolted in place with a nut or screw. A few methods for removing the brake light switch trailblazer have been outlined below.
The first method uses a socket wrench and reverses the threaded bolt remover tool on the bolt head under the switch. The second option is by drilling out the rivets, holding them in place, and then prying them off with a metal wedge if necessary.
The final way is cutting through its wires with wire cutters after disconnecting them from their connectors at both ends of the vehicle wiring harness. Continue reading this blog post to find more.
8 Methods on How to Remove Brake Light Switch Trailblazer:
Method 1: by Using a Screwdriver.
Lift the brake pedal with either your foot or use a stool to do so. Locate the screws along the bottom side of your brake light switch, and remove them. Use an adjustable wrench to loosen the wiring; try not to twist it as you do this. Pull the wiring off your brake light switch and set it to the side.
Method 2: by Using a Flat Head Screwdriver.
To change the brake light switch, you must first lift the brake pedal with your foot or a stool. Then, locate the screws along the bottom side of the brake light switch and remove them. Next, use a flat head screwdriver to pry open the clips holding the brake light switch in place. Finally, fit the flat end of the screwdriver into the slight gap between the clip and the brake light switch.
Carefully wiggle it up or down until you can fit another screwdriver under there to continue prying it open. Once one side of the clip is off, use a pair of needle-nose pliers, grab the wire (or wires depending on your car), and pull it out slowly.
Method 3: Use a Socket Wrench and Socket.
Lift the brake pedal with either your foot or use a stool to do so. Use a socket and a socket wrench to remove the two bolts holding your brake light switch in place, do not discard these bolts as you will need them again! Next, pull the wiring off your brake light switch and set it to the side.
Method 4: by Using a Drive Ratchet.
Lift the brake pedal with either your foot or anything you found useful. Use a 3/8 inch drive ratchet with a 13mm deep socket attached to remove the two bolts holding your brake light switch in place, do not discard these bolts as you will need them again! Next, pull the wiring off your brake light switch and set it to the side.
Method 5: Cutting Through the Wires With a Wirecutter
There is a simple method for removing the brake light switch, which is very effective and safe. This method involves clipping through the wires, stopping the circuit from completing itself when you activate your brakes.
You can use this method to remove any of the attached components to the brake pedal mechanism. However, remember that this method will require a higher current to activate the brakes after removing components from the pedal mechanism.
Method 6: Removing Brake Light by Prying Off Metal Lever
The next method is very effective but can be potentially dangerous. This method involves using a screwdriver or any other long rod to remove the brake light switch by prying up the metal lever which holds it in place.
You can use this method to remove any of the attached components to the brake pedal mechanism. However, remember that this method will require a higher current to activate the brakes after removing components from the pedal mechanism.
Method 7: by Thin Pry a Thin Metal Wire
Slowly lift on the brake pedal while continuing to pry with wire until the end of contact is reached, at which point you can slide out or cut off this thin metal wire. At most, if your wire is not thin enough, it will take 3 attempts before removing the brake light switch assembly can be achieved.
Method 8: By Removing the Brake Pedal
It has been found that one can remove the brake light switch assembly by first removing the brake pedal itself. How this is done depends on whether or not you have a manual transmission vehicle or an automatic transmission vehicle.
If you have a manual transmission, find the bolts that hold it from underneath and go ahead and remove it. If you have an automatic transmission, then pull up on the brake pedal with two hands to ensure that the master cylinder is not releasing any fluid.
Precautions and Warnings On How to Remove Brake Light Switch Trailblazer:
1. The brake light switch is only used when the vehicle is in reverse. If you remove this switch, there is no way to activate the brake lights. They will not come on until the car moves out of reverse.
2. When removing the switch, disconnect the electrical connector first, then use a pair of pliers to remove the retaining clip. The last thing you want is some boiling oil or brake fluid to come squirting into your face when you take out this part.
3. If the brake light still does not work after replacing the switch, there may be something wrong with the brake light bulb.
4. Do not forget to re-attach the ground wire.
5. If you’re working with cars or electrical wires, be very careful not to touch any wires carrying current or voltage. If you do, you could get seriously hurt or even die.
Conclusion:
The trailblazer brake light switch is a part of the electrical system that allows you to signal other drivers when your vehicle has stopped. It can be removed in a few easy steps, and once it’s been repaired or replaced, this will need to be done again each time the car battery dies.
For more information on removing the brake light switch trailblazer without any difficulty, follow these instructions carefully. You may want to enlist a professional if you are worried about damaging any other car parts. Let us know how it goes in the comment section below!
