How to Start a Car With a Screwdriver and Hammer
If you find yourself in a situation where you need to start your car but don’t have access to a traditional ignition key, you can use a few methods to get the engine running. One option is to use a screwdriver and hammer to bypass the lock cylinder.
In this blog post, we will cover how to start a car with a screwdriver and hammer. Believe it or not, you can start a car with a screwdriver and hammer. All you need to do is follow these simple steps. So keep reading this blog post till the end!
How to Start a Car With a Screwdriver and Hammer
Step 1: Supplies
You will need to find a car with the hood up. Once you have a car with a hood, get a screwdriver and hammer.
Step 2: Car Selection
First, you must find a running car that has the hood open. Next, you should check to see if the person is aware of your presence. If they are not looking at their car engine, tap them on the shoulder and ask for some change. If they know your presence, ask them if you can use their car to start it.
Step 3: Engaging the Car
Go up to the driver’s side door and open it. Look down and locate an object covered by a carpet (a screwdriver). Place the head of this object onto a metal part (the car frame) and lift the end of the screwdriver closest to you. You should then hear a clicking noise that lets you know you are neutral.
Step 4: Hammer Time
Now, identify the hood latch under the car’s hood. Position your screwdriver right next to it to press against the metal. Then, use your hammer to hit the end of the screwdriver. This should break open the hood latch.
Step 5: Chop Screwdriver Shaft Off
Once the hood latch is open, cut the end of your screwdriver off with a hacksaw. This makes it easier to start the car. You can then go back around behind the car and pull up on the hood to open it.
Step 6: Put Your Foot On The Throttle
Find a comfortable spot near the area under the steering wheel where you think you could place your foot without being in danger of hurting yourself or others. If this is not possible, you should place your foot on the side of the throttle instead.
Step 7: Slot Screwdriver Handle
Slide the handle of your screwdriver into the slot that appears along the bottom of your car’s dashboard. This will cause your screwdriver to lock into place, which makes it easier for you to start the car later.
Step 8: Turn Screwdriver
Turn your screwdriver counterclockwise until you hear a clicking noise. This is the sound of your screwdriver engaging with your car’s ignition system, which is turned on when it moves in this direction.
Step 9: Epoxy Key to Screwdriver
While your screwdriver is engaged with your car’s ignition system, carefully take the handle of your key and epoxy it to the end of your screwdriver. This makes it much harder for you to lose track of where you are in this process when you are trying to start the car later.
Step 10: Induce Vibration
Put on some heavy-duty earmuffs to create a large amount of noise. If you don’t have any earmuffs, this is the point at which you should turn up your car’s radio as high as it will go while still maintaining some semblance of sound quality.
Then, it would help if you turned the screwdriver counterclockwise again to engage with your car. But, again, this is very loud and may result in some permanent hearing damage, so you may want to wear earplugs along with the earmuffs.
You can also check out to Make the Groundskeeper Hammer His Thumb
Some Tips and Suggestions
Here are some tips and suggestions on how to start a car with a screwdriver and hammer.
1. Make sure the engine is turned off.
2. Make sure you have a screwdriver and hammer before attempting this.
3. If the car is a stick shift, make sure you have a screwdriver and hammer before attempting this.
4. If your car is automatic, turning the key in the ignition should be fine while simultaneously holding down the brake pedal with one foot and pressing on the gas pedal with another. Of course, this does not always work, but it has never failed me before.
5. When you turn the key, make sure to do so with finesse and not too fast or too slow. If done correctly, there should be a power light that will shine on the dash that doesn’t usually shine when the car is off.
6. In case of a stick shift, try starting it up as an automatic first by placing it in drive, making sure the parking brake is on to prevent it from rolling away, and then turning the key.
7. The car should start after five or six tries. If the vehicle doesn’t start after ten minutes of trying this method, you’re probably better off just taking your vehicle to a mechanic.
Precautions and Warnings
1. If the screwdriver slips, it could injure you.
2. If the battery is charged (normally) enough to give an electrical shock, it is also charged with enough electricity to kill you. This procedure should be used only on cars that won’t start without jump-starting, which excludes most new cars these days and older cars that don’t have this problem.
3. Don’t hold your hands near the battery when trying to start it, and be sure to go in the correct order and on time.
4. The screwdriver might spark when starting the car. Make sure it isn’t underneath any flammable materials.
5. The car should be turned off before performing this procedure, and the battery should be removed (if possible) or covered (with something like duct tape) to prevent sparks during the process of jumping the car with a screwdriver and hammer.
6. Don’t let the screwdriver touch anything but the car battery; it might short-circuit something and start a fire, which could burn you or cause other injuries.
What Are the Benefits of Using a Screwdriver and Hammer to Start a Car
There are no benefits of using a screwdriver and hammer to start a car. This method of starting an automobile is very dangerous. It may cause serious injury, or even death, through electrocution or head trauma from the car’s agitated state.
Additionally, doing this will void your warranty with almost every automotive manufacturer on the market (meaning that any attempt to start the vehicle in such a manner will render your warranty null and void).
What Is the Difference Between Hand Tools and Power Tools for Starting Cars
Many modern cars are equipped with an immobilizer system to reduce car theft. When the car is turned off, this system requires a key or code to allow the car to be started. Always consult your owner’s manual for information on starting your particular make and model of vehicle. Other types of cars may need other procedures to be followed for starting the car.
A screwdriver and hammer can be used to start a car instead of a key, but this should only be performed as a last resort. Note that these tools are not preferred methods of starting a car, as they require a lot more work than launching an engine with an actual ignition key or an electronic key-fob.
You Can Check It Out to: Remove Stripped Wheel Stud
Conclusion
If you’re ever stranded with a dead battery, there are several ways to start your car. The most popular methods involve using jumper cables or a portable jump starter. But if these aren’t available and the weather is inclement, fear not! There’s always the screwdriver method which can be used in conjunction with a hammer to generate enough power for your engine to turn over.
The steps mentioned on how to start a car with a screwdriver and hammer are easy enough for anyone, so even if you’re not mechanically inclined, it’s worth trying this technique just once! We hope this was helpful information. Have any of our readers had success starting their vehicle with these methods? Let us know below!
Louis Wein
Louis has always been fascinated by cars. He loves the way they look, the sound of the engine, and how they make him feel when he's driving. He is always keen to learn more about different mechanics of cars and how the engine contributes to other aspects of the car. As an automotive technician with over 10 years of experience, he knew how they worked and loved taking them apart to see how they went back together. He was especially interested in the mechanics of combustion engines and loved finding ways to make them more efficient. He loves to work on cars and help people keep their vehicles running smoothly. As a senior editor, he enjoys contributing to Diy quickly because it allows him to share his knowledge and expertise with others.
