How to Make a Redstone Clock That Turns on and Off

In this blog post, we will go over how to make a redstone clock that turns on and off. Redstone clocks are relatively simple, but they can be quite complex in design. To build a working Redstone clock, you need a few things Redstone dust, pistons, sticky pistons, repeaters, wire, and preferably some other materials such as buttons or levers. 

We will explore the different types of these components below, so stay tuned! Once you have gathered all of your materials, it’s time for us to get started building your very own red stone clock! The purpose of this blog post is to inform readers about how to create a Red Stone Clock that functions appropriately. So read on to know more!

How to Make a Redstone Clock That Turns on and Off

8 Ways on How to Make a Redstone Clock That Turns on and Off:

1. Build a T Flip-Flop:

This is a simple way to make a clock. To build one, you need a T-flip flop and a Redstone lamp. To start, power the T flip-flop with a lever or button. Then put the Redstone lamp next to it and then right-click on the side of the T flip-flop that has a dot. After you have done that, the T flip-flop should power up and turn back off after a short time. If it doesn’t turn off, try powering it with a redstone torch instead.

2. Build a Daylight Sensor Clock:

This is another simple way to make a clock. To start this clock, put Redstone blocks in front of a daylight sensor so it can get light from the sun. Then add a clock circuit and add it to the daylight sensor. Now, when the sun turns the daylight sensor, it will also power up your clock circuit connected to it!

3. Use a Redstone Repeater:

To make a clock, you need a row of Redstone repeaters and Redstone dust. Place the repeaters in a row and add the dust to the bottom, facing into the row of repeaters.

Then, extend the line of Redstone dust back until it has reached its starting position (the one in front of the brick block). Next, add another row of Redstone repeaters in front of the line of Redstone dust that you just made. Keep going until you have a nice long line. Then, power up all of the repeaters and put a block above them to activate them!

4. Make a Ticking Sign:

To build this, first put up a sign on your wall. Then power the first line of Redstone on either side of the sign with Redstone dust, so it is connected. To power it, you can use the button or any other lever! Next, add another line on top of that one and then connect these two lines with Redstone dust. Do this until you have a good size ticking sign! Finally, place Redstone repeaters every two blocks or so. When you are finished, hit the button or lever and watch your sign tick! You can also use this method to create a clock!

First Put Up a Sign on Your Wall

5. Use a Clock Circuit:

To do this method, you only need Redstone dust and Redstone blocks. So first place down some Redstone dust, then right-clicks on it with a Redstone block to power it. Now keep adding more Redstone dust and blocks to the line until you have an excellent ticking signal! Place an Observer down on the line of Redstone blocks and blocks of dust, and it will then emit a signal every time the Observer detects changes. So now you can use the Observer to do anything from powering machines to sending messages to players.

6. Build a Monostable Circuit:

The monostable circuit, also known as a one-shot multivibrator, is a digital circuit that gives rise to a single pulse in response to the trigger voltage. After the initial trigger input, the monostable output stays high until triggered again, at which time it resets to zero. The time interval between the trigger and the output pulse is controlled by a capacitor and a resistor. The capacitor charges gradually via the resistor until it reaches the trigger voltage, at which point the circuit changes state.

To make a monostable circuit, you need to power up a Redstone torch with some Redstone dust, put a repeater next to the Redstone dust, and set it on one of its sides to give a negative delay. Finally, put a block on top of the repeater to make it stay off after you power it up.

7. Build an RS-NOR Latch:

It puts on a signal when all signals are changed to off or on simultaneously. To make this clock, power up a Redstone torch and put down some Redstone dust which you will need to do for all of these methods. Then place a block on the last line of Redstone dust, put a repeater on one side of it, and set it to the negative delay. Now connect that repeater’s end with another line of Redstone dust and put a block to activate it.

8. Build an Edge Detector:

To make this clock, place down two sets of Redstone blocks (one on each side) and then add some Redstone dust to get the power started. Then add a repeater with the negative delay and connect it to one of the Redstone blocks. Finally, add a block in front of the repeater to turn it on! That’s all there is to making clocks in Minecraft!

Some Tips and Suggestions:

Pistons can be used to push Redstone wire up
  1. Redstone wire can be placed on the top of glowstone, upside-down slabs, upside-down stairs, and trapdoors.
  2. Pistons can be used to push Redstone wire up. Place it back down after raising it with a piston, right-click with an empty hand while pointing to where you want the wire to go.
  3. Pistons can be used to push and pull blocks, even if they cannot be moved by hand. To make a piston pull a block, place Redstone wire behind the piston (where it would generally extend) and attach a repeater set to 4 or more ticks (4 or more seconds).
  4. Pistons can’t move bedrock or any transparent, full blocks.
  5. Slime blocks can move Redstone wire when pushed by pistons, making them great for traps and devices that need to be hidden under the floor.
  6. Redstone wire can be put on the sides of other blocks, but it will not connect to blocks if an air block is in the way.
  7. Redstone wire will connect to blocks that do not have Redstone wire on them, but it will not connect back, making it possible to split the signal in two.
  8. A single dot of Redstone dust can be placed next to a block without causing any problems with the circuit. However, if there are multiple dots next to it, it will disconnect.


In this blog post, we learned how to make a redstone clock that turns on and off. The methods are not difficult, but it does take some time to set up the circuit. If you want to make your own Redstone clock that turns on and off, then this blog post will be helpful for you.

The instructions are straightforward enough for someone with little experience in Minecraft modding to follow them easily. However, we hope these steps will help you get started making a Redstone-powered timepiece of your very own! Let us know your thoughts in the comments below!

Jennifer Branett
We will be happy to hear your thoughts

Leave a reply

DIY Quickly