How to Square a Board Without a Jointer

August 22, 2022 0

Introduction

You may have reached a certain point where you need to square up the board. But wait a minute! Did you lose your jointer? What are you going to do now? Are you leaving the task and going out buying a new one? There are many questions, and before you get puzzled between them, I have got good news for you. You can flatten a board without the use of a jointer. So, stay with me till the end to know how to flatten a board without a jointer.

A jointer is needed for squaring aboard, but you can still work without using the jointer and make your wooden board square perfectly. Yes, you have heard that right; in this article, I will show you how to square a board without a jointer in the simplest ways. So, let’s dive in!

Processes How To Square A Board Without A Jointer

Process One:

Measure the board and draw a straight line on one end of it.
Cut the wood in half to make two pieces, then cut that left side down until you reach your drawn line.
Now align these two boards with each other from both ends by matching their faces as shown below. Basically, what we have done so far is create four lines across our workpiece (in this case, a piece of lumber). And now take another scrap piece for support while cutting off excess pieces at either end.
This will give us an accurate square shape! Make sure you use clamps/wrenches when doing this step so there are no chances of shifting or sliding out of place before making any cuts! You can also do this step by using a hand saw to start off, then switch over to the table saw.
Now we need to make two more cuts on the board until it is exactly as long and wide as it needs to be (to use for whatever project you have in mind).
After that all there’s left is taking your newly-cut piece of lumber and cleaning up any excess pieces with sandpaper or an electric sander! And voila – you’ve created a square without the help of a jointer.

Process Two:

You can accomplish this process with your table saw and a planer. You can even sand the surface and make it smooth on the table saw without any hassle. It does have a good sharp blade, and it can be done easily. You can also use a belt sander to make the surface of your workpiece smooth and free from scratches.

As you are about to make some square pieces, you have to first identify the correct measurement of your wood piece. A square piece should have an accurate measurement from each side. If you cut the piece in an irregular shape, it will not be a square one. Now use a saw to cut your wood piece according to the size that you have determined earlier. If you are using a power saw, hold the wood firmly with both hands.

Once you get the measurement, you have to start working with the table saw. I am going to get my first cut through the rough edges.So, I will put my rough wood on the table saw. So, I hold the wood piece tight to the fence and guide through as straight as I can. You have to keep your fingers away from the blade. You can also use some special clamps to hold it in place. After that, you will have to adjust the blade according to the thickness of the wood.

It is recommended to use adequate safety features to avoid accidents. You would probably not want to push your finger inside the saw; that’s why it will be better if you push it with scrap wood. If you need to smoothen the edges, you can place the wood piece upward and push it in the same process. Thus, your square wooden piece will be ready. As you can see, a finger joint jig is an excellent and simple way to join two pieces of wood. If you want to try it, you can just follow the steps mentioned above and make your own jig.

Precautions

The board being squared must be at least twice as wide as the desired width of the finished piece.
Use a square to line up one edge with an outside corner and clamp it in place.
Square off two opposite sides, then remove the clamps so you can test your work on the other end. Make sure they’re parallel before finishing them—if not, call it done and start over again.

Frequently Asked Questions

Is Jointer Harmful?

If you don’t have a jointer, there’s no need for despair. You can still square boards with just an edge guide and some good old-fashioned hand tools (or power tools if you’re into that sort of thing). In all seriousness, though, the process is not terribly difficult to understand, but it does take time.

Which Saw is Better to Use For this Process?

The simplest way to square a board without using a jointer is by using the rip fence on your table saw. Your first step will be to measure the width of the cut being taken about where you will want one edge of your newly squared board positioned.

You’ll need this measurement to add up exactly with half an inch so that there are two separate sides at ¾ inches when you run it through. If they don’t match, then adjust and make sure they do before moving forward.

Conclusion

Lastly, we hope that the processes we have stated here will help make a square board without a jointer. Make sure to have safety protection while using the saw and other sharp objects. Thank you and have a nice day.

You May Read Also . How to Make Coin Hole Boards