How to Fix Bent Wooden Door
One of the most common problems people encounter when working on their homes is a broken wooden door. Whether it’s a front door, garage door, or even an interior closet door, there is nothing more frustrating than dealing with a bent and damaged piece of wood. Fortunately, repairing your bent wooden doors will be easy if you have some essential tools and know what you’re doing!
In this blog post, we will discuss how to fix bent wooden door. When we think about our house, we usually believe that everything should be perfect in every way; nevertheless, things occur beyond our control, such as minor accidents like chipping off pieces of the paint around doorframes, leaving them looking unprofessional and incomplete. Read on to know more!
Summary: You can fix a bent door by using a door hinge repair kit. First, measure the distance between the door and the jamb. This measurement will identify the size of the hinge needed. Second, find the correct hinge kit for your door. Third, remove the old hinge by removing the screws that hold it in place. Fourth, replace the hinge with the new one by following the instructions in the kit. Fifth, reattach the screws and test the door to make sure it functions properly.
10 Ways on How to Fix Bent Wooden Door:
1. Slip a Piece of Wood Under It
If you have a hardwood door, it may be possible to fix the bent door. This is accomplished by slipping a piece of exterior grade plywood or other large flat pieces of wood under the door at one of the hinges.
If necessary, remove the hinge pins and remove the door from its hinges, slip a piece of wood between the door and the jamb, replace the hinge pins. Finally, replace the door on its hinges. If you’ve ever seen bent floors in an old house, this is how carpenters used to fix their floors.
2. Use a Hammer and Screws
If you can hammer small nails into the warped door, use a hammer and a few small nails to fix the problem. If you hammer the nails partially into the door but not all the way, it will pull the wood fibers into the line up with each other and fix the problem.
3. Use an Angle Iron to Straighten It
If the wood is not warped too much, you can use angle iron. You’ll need two pieces of angle iron, and one piece should be about 1 inch wide and 4 feet long with a small half-moon-shaped cutout on one end. Lay this piece of metal flat against the jamb, then place the door on it. The cutout end should be placed at the top of the jamb with the decorative curve pointing toward the floor.
The other piece of angle iron should be about 2 feet long, and it can be as wide as you like. Place this piece of metal on the bottom rail of the door, with its decorative curve pointing toward you. Hammer small nails through the two pieces of metal where they cross to hold them together.
4. Use Shims to Straighten It
If you can’t use nails to fix the problem, use shims. Use a pair of chalk lines with wooden sticks on one end and a piece of string on the other end. Run these strings up and down both sides of the door and mark any warped areas with small pieces of chalk. Put masking tape over those marks; this tape will prevent you from damaging the paint on the door. Next, use a block of wood to hammer some shims in place under those marks.
5. Heat It and Pull It Out
If you have an iron or steel fire poker, heat it hot with some propane burners. Touch the poker against one side of the door to straighten it. Hold the poker against that side for a couple of seconds to transfer some heat through it, then use your chosen pry bar under the edge and pull out away from the bent area.
6. Use Polyurethane Foam to Straighten It
If you can’t use mechanical methods to fix bent wooden doors, use a can of expanding foam. Start by gently pushing the door against the jamb to see if it will close easily.
If not, you’ll have to remove the hinge pins and take off that side of the door. Once you have removed that part of the door from its hinges, spray foam into the gap just above the hinge. When the foam starts to harden, push the door flat against the jamb with your hand or foot, so it bends back into place.
7. Use a Block Plane
If the door is warped, you can use a block plane to fix it. Put masking tape across the area where you want to plane off some wood; this will help prevent damage to the paint on the door. Use these marks as your guide and plane off small amounts of wood until necessary. Don’t take off too much, or you’ll have a hole in the door. The plane off just enough to flatten it out.
8. Use a Belt Sander to Straighten It
If the door is warped, use an electric belt sander (never hand-sander) with 50 grit sandpaper and move your piece of wood up and down the belt while it rotates. Be careful not to go too fast, or you’ll sand through the door. Also, switch your belt sander over to its flat side before using it; otherwise, you might burn the wood with the speed of the spinning belt.
9. Use a Heavy Coat Hanger
If you can’t use any of these methods to fix the door, try hanging on to the bottom rail of the bent area with one hand while nailing a large, heavy coat hanger onto the side directly opposite it.
Bend the coat hanger until it fits in with the curve of the door and is parallel to it. Then, place a small nail through the bent area to keep it in place while you hammer a large brad into where there is just space between the two doors.
10. Attach a Board to the Inside
If that doesn’t work, put a board between the two doors and attach it with nails. The nails should be placed in line with the hinges on one side, and the other end should go into place over where you want to straighten out your door from.
Hammer small brads between the two boards and use a level to make sure they are straight. When you see that they’re even, nail them in place using large brads on either side. That should hold the door flat until you can talk to a carpenter about it.
Conclusion:
In conclusion, bent doors are a common problem in homes. The best way to fix them is to adjust the hinges so that they’re even and tighten all screws. You can also use wood glue or liquid nails if you want an extra-strong bond on your new door hinge.
A bent door can be a nuisance, but it is pretty fixable. The process of fixing a wooden door with a bow in the middle starts by unscrewing and removing any hinges on either side of the bowed area.
Screw them together tightly for stability; then screw one board into place using three or four long deck screws through holes drilled about half-inch deep into studs inside wall frame cavities near where you want your new doorway cut out.
As you can see, there’s no need to call in a carpenter when your door needs fixing. However, now that you know the simple steps for how to fix bent wooden door, why not give it a try!
You Can Check it Out to Hang Wood Panel Art
