How to Fix a Broken Metal Bed Frame

Fixing a broken metal bed frame can be tricky and difficult. It is important to know what you’re getting into before you start, or else the situation could worsen. In this blog post, we will show you how to fix a broken metal bed frame with ease by following these simple steps!

How To Fix A Broken Metal Bed Frame

Materials Needed

  • A drill
  • ½ inch metal screws with screwdriver bit
  • Ladder or step stool
  • Metal bed frame 
  • Protective eyewear
  • Gloves (optional)
Metal Bed Frame

Instructions: How to Fix a Broken Metal Bed Frame

Step One: Remove the broken pieces

The best way to remove old screws is to use a drill and screwdriver bit. Drill down into the screw until it becomes loose. Then, unscrew it by hand or use pliers if necessary.

Remove The Broken Pieces

Step Two: Replace broken parts with new ones that match

You’ll want to replace the broken parts with new ones that match. These may be found in a hardware store, or you might have some lying around your house!

Step Three: Reattach the bed frame and tighten screws

Once you’ve put all the pieces back together, you need to make sure they’re all tight. You can use a screwdriver to tighten screws from inside the bed frame, and then you’ll want to use your hand or pliers on any stubborn screws that don’t seem to be tightening properly.

Step Four: Test out new bolts.

Once all of the pieces are reassembled, it’s important to make sure they’re working as they should. You’ll want to test out any new bolts you’ve installed by pulling on the frame and checking for movement or wobbling.

Step Five: Re-attach bedding.

Finish the project by re-attaching all of your bedding and mattress, as well as checking for any loose or broken parts. Make sure that everything is in working order before using it again!

What Causes a Bed Frame to Break?

  • Older bed frames are more likely to break as the metal becomes brittle over time.
  • People who frequently move their beds place a higher strain on the frame. Moving furniture and appliances in your home also puts stress on bed frames.
  • Bed frames with a broken joint are more likely to break completely.
  • A bed frame can break if the area is not properly reinforced.
  • If you find your bed frame has a broken area, it is time to call the experts.

Things To Consider For Broken Metal Bed Frame

Things To Consider For Broken Metal Bed Frame
  • Always use the right tools for the job. This means using a claw hammer to remove nails and tapered pliers or needle-nose pliers to help bend metal pieces back into place.
  • An important first step is always to identify what type of steel you’re dealing with, as this will inform your approach on how best to fix it. Identifying types can be done by looking at their surface finish (flat ground vs. rough) and if there are any markings on the side that could denote their composition.
  • When repairing bent corners, take note of how many bends are present to determine which technique should be used: one bend needs light tapping; two bends calls for a heavy tap followed by bending both ends towards each other; three bends requires a heavy tap, twisting the corner and bending both ends towards each other.
  • Hammering on one bent area without first straightening it out with pliers will result in the metal spreading in that direction to create two separate areas instead of just one.
  • Use increasingly firm blows with a rubber mallet or steel plate until you hear or feel the piece give way under pressure. For maximum leverage, place your fingers as close to the point where you’re hitting as possible.
  • Take care not to overdo it when bending sheets back up again so they don’t tear from being pulled in different directions by force (this will cause more work later). Make sure that all bends are uniform before proceeding.

Precautions Before Fixing a Broken Metal Bed Frame

  • When you first start applying pressure, do not apply force across wide surfaces as this will create large cracks. Instead, apply force in one direction at a time to gauge the metal’s flexibility and determine which way it will bend before making any additional adjustments.
  • Use gloves when handling sharp metal edges; also, wear protective eyewear while hammering since there will be shards flying about as well as an increased risk of getting hit by flying objects.
  • Place a drop cloth over the carpeted surface of your bedroom to protect it from scratches and dirt.
  • Layout all tools needed beforehand so you don’t have to waste time fishing through drawers for things later on.
  • If fixing with one person, ask someone else present in the room to help hold pieces if they’re coming up too high or low again before bending them back into place (or use clamps).
  • While you’re hammering away at the metal, have your assistant hold up the pieces that need to be straightened. This will prevent you from having to reach through sharp edges and risk injury.
  • Use power tools when necessary if there is no other option but always wear protective eyewear when operating these devices since they can cause injury.

Some Tips & Advice To Protect Your Metal Bed Frame

Some Tips & Advice To Protect Your Metal Bed Frame

Tip 1: Inspect the bed frame monthly and tighten any bolts or screws that are loose

Tip 2: Be sure to pick up your bed during a move, even if you don’t think it needs to be done.

Tip 3: Avoid putting anything on top of the metal mattress support rail. You can cover this with fitted sheets for decorative purposes.

Tip 4: Keep the metal bed frame in good shape by using a mattress topper.

Tip 5: Place decorative pillows on top of your headboard and not under it so they do not get damaged from constant contact with the metal.

Tip 6: Keep your metal bed frame clean and dustless by brushing it off.

Tip 7: Be careful not to scratch or scuff the frame when moving it in order to keep its new look.

Tip 8: Use a mattress pad cover on top of your mattresses which will protect the surface from stains, wrinkles, spills, and wear spots while providing comfort for you at night.

Frequently Asked Questions on How To Fix A Broken Metal Bed Frame

How to Avoid Bed Breakage?

To avoid bed breakage, make sure the frame is solid and stable. Avoid beds with headboards, footboards, or metal rails that are screwed onto the frame; these attachments will weaken the structure over time.

How Do I Put a Metal Bed Frame Back Together?

To put it back together, you should have two nuts for each bolt. One nut that screws onto the threaded part of the bolt (facing away from where it connects) and another nut that goes between this first one and tightens against it so they don’t loosen up again. Tighten all bolts using an adjustable wrench until there is no slack in them, but do not overtighten.

How Do I Fix A Metal Bed Frame That Slouches?

If your metal bed is slouching, you can use blocks to raise one end up so that it’s even again; for example, if only one side has sunk, then stack some books under that leg until it rises back up (be sure they are stable enough). This will help keep everything balanced.

How Do I Know if My Metal Bed Frame Is Broken?

There are several ways to tell if your Metal Bed Frame is broken. One way is to look for cracks in the metal bed frame itself. Another way is to see if there are any pieces missing or bent at odd angles from where they should go.

The mattress on top of the frame could also break through any openings due to poor quality workmanship when attaching a headboard or footboard onto the backside of this metal bed frame (this is common with poorly-made welds).

There may also be sharp edges around these cuts which can pose safety hazards for anyone who touches them. If you notice anything that looks suspicious, it is best to fix this before it gets worse and causes a large breakage of the entire bed structure.

You Can Check It Out To Fix a Broken Box Spring


It is important to remember that a metal bed frame can be the most comfortable and supportive sleep surface for your mattress. But let’s be honest, you can never have too many spare bed frames. Whether it’s for guests or the inevitable need to replace one that breaks down as metal beds age, they are always a good investment!

This blog post has given you some great tips on how to fix a broken metal bed frame, and we hope this information will help give your home a new look without having to purchase an entirely new bed set.

You may read also: How To Shorten A Bedskirt

Elizabeth Davis

Elizabeth Davis

Elizabeth is a creative writer and digital editor based in the United States. She has a passion for the arts and crafts, which she developed from a young age. Elizabeth has always loved experimenting with new mediums and sharing her work with others. When she started blogging, she knew that DIYquickly would be the perfect platform to share her tutorials and tips. She's been writing for the blog from the beginning, and her readers love her helpful advice and easy-to-follow instructions. When she's not writing or editing, Elizabeth enjoys spending time with her family and friends.

We will be happy to hear your thoughts

Leave a reply

DIY Quickly