How to Pick a Car Trunk Lock
There are a few ways to pick a car trunk lock. Suppose you know what you’re doing and processing. However, it can be quite tricky if you’re not familiar with doing it. This article will discuss the various methods for picking a car trunk lock and provide step-by-step instructions on how to pick a car trunk lock.
We’ll also offer tips on choosing the right lock pick set for the job. So whether you’re a professional locksmith or just someone who needs to get into their car trunk, read on for all the information you need.
Car trunk locks are designed to be very secure. That’s why most of them are rather complicated to open. They’re made up of pin tumbler cores, wafer cylinders, and tubular locks. The former is the most common type, while the latter is rare.
A Detailed Guide on How to Pick a Car Trunk Lock
Way 1: Pick a Car Trunk Lock with Paper Clips
Steps:
- Straighten the paper clips by gently bending them with your fingers.
- Insert one end of a straightened paper clip into the bottom (hole) of the lock and push it down to where you can’t see it anymore.
- Push the other end of the paper clip up from the outside to catch on the part of the lock’s mechanism. You can get a good idea of which part to push it toward based on where you hear clicking sounds when you wiggle it in different places.
- Once you’ve got the wire caught, pull gently until one side opens up and then quickly press this side into a vertical position while at the same time pushing down with your thumb on the other side that is still hanging straight down.
- Repeat these steps until both sides have been pushed down simultaneously, thus opening up your trunk lock without any damage being caused to it.
Way 2: Wrench Coat Hanger and Flashlight
What You Need
- A wrench that fits the lock
- A long, skinny coat hanger or another wire object that can fit into the gap of the keyhole 1 cm down from its top (see diagram below)
- Flashlight (cellphone light will do in a pinch)
Steps:
1. Straighten out a coat hanger and then use pliers to cut off any hooking parts on it, so all you’re left with is a long, straight piece of metal. There’s no need to be throwaway about this, as you’ll only throw it away after picking your lock.
You can also do this step by sticking a small wide flathead screwdriver (e.g., for eyeglasses) into the gap where you see the horizontal line of metal inside your lock’s keyhole and pulling down until the entire piece of metal is straightened out. However, using this method may cause minor dents on your lock or scratch up your screwdriver, so be careful if you decide to use this method instead.
2. Stick one end of your coat hanger wire deep down into the bottom hole of the car trunk lock after hooking it through from the outside, as shown in diagram #1 below:
3. Angle your flashlight at a low-to-medium angle directly into that part of the trunk lock where you just shoved in that wire at the top, as shown in diagram #2 below:
4. With your other hand, push down on the keyhole of the keylock to level with the bottom part you just pushed your wire into. Push it down until you can see or feel a “catch” holding onto your coat hanger wire. Let go of the keyhole and then pull out your coat hanger wire very slowly until one side pops up about 1 cm high, which should be enough to give you some space to work with what will now look something like Diagram 3 (see next page).
5. Keep pulling down very slowly on where the pink arrow is pointing (in diagram #3) until both sides catch again simultaneously, which should unlock the car trunk lock.
Way 3: Using a Screwdriver
Steps:
1. Straighten out both ends of the wire clothes hanger so that all you’re left with is a long, straight piece of metal. There’s no need to be throwaway about this, as you’ll only throw it away after picking your lock.
You can also do this step by sticking a small wide flathead screwdriver (e.g., for eyeglasses) into the gap where you see the horizontal line of metal inside your lock’s keyhole and pulling down until the entire piece of metal is straightened out. However, using this method may cause minor dents on your lock or scratch up your screwdriver, so be careful if you decide to use this method instead.
2. Stick one end of your wire deep down into the bottom hole of the car trunk lock after hooking it through from the outside.
3. Angle your flashlight at a low-to-medium angle directly into that part of the trunk lock where you just shoved in that wire at the top.
4. With your other hand, push down on the keyhole of the keylock to level with the bottom part you just pushed your wire into. Push it down until you can see or feel a “catch” holding onto your coat hanger wire. Let go of the keyhole and then pull out your coat hanger wire very slowly until one side pops up about 1 cm high, which should be enough to give you some space to work with.
5. Keep pulling down very slowly on where the pink arrow is pointing until both sides catch again at simultaneously your, which should unlock the car trunk lock.
Way 4: Using a Magnet
Steps:
1. Straighten out both ends of the wire clothes hanger so that all you’re left with is a long, straight piece of metal. There’s no need to be throwaway about this, as you’ll only throw it away after picking your lock.
2. Stick one end of your wire deep down into the bottom hole of the car trunk lock after hooking it through from the outside.
3. Angle your flashlight at a low-to-medium angle directly into that part of the trunk lock where you just shoved in that wire at the top.
4. With your other hand, push down on the keyhole of the keylock to level with the bottom part you just pushed your wire into and hold it down.
5. Hold one side of the magnet against that keyhole the same way you’ve been pushing on it with your other hand, then pull out your coat hanger wire very slowly until both sides catch simultaneously, which should unlock the car trunk lock.
Way 5: Using a Slim Jim
Steps:
1. Straighten out both ends of the wire clothes hanger so that all you’re left with is a long, straight piece of metal. There’s no need to be throwaway about this, as you’ll only throw it away after picking your lock.
2. Stick one end of your wire deep down into the bottom hole of the car trunk lock after hooking it through from the outside.
3. Angle your flashlight at a low-to-medium angle directly into that part of the trunk lock where you just shoved in that wire at the top and hold it down while adjusting its position until you can see or feel a “catch” holding onto your coat hanger wire when holding keyhole level with the bottom part of a lock where you just pushed your wire into.
4. With your other hand, push down on the keyhole of the keylock so that it’s level with the bottom part of the lock where you just pushed your coat hanger wire into and hold it down while adjusting its position until one side pops up about 1 cm high, which should be enough to give you some space to work with.
5. Pull out your coat hanger wire very slowly until both sides catch at simultaneously your, which should unlock the car trunk lock.
You Can Check It Out to: Hook Up Fuel Pressure Regulator
Way 6: Using a Lock Pick Set
Steps:
1. Straighten out both ends of the wire clothes hanger so that all you’re left with is a long, straight piece of metal. There’s no need to be throwaway about this, as you’ll only throw it away after picking your lock.
2. Stick one end of your wire deep down into the bottom hole of the car trunk lock after hooking it through from the outside.
3. Angle your flashlight at a low-to-medium angle directly into that part of the trunk lock where you just shoved in that wire at the top and hold it down while adjusting its position until you can see or feel a “catch” holding onto your coat hanger wire when holding keyhole level with the bottom part of a lock where you just pushed your coat hanger wire into, which should unlock car trunk without affecting ignition switch functions like push start button and electronic locks (if equipped).
4. With your other hand, push down on the keyhole of the keylock so that it’s level with the bottom part of the lock where you just pushed in your coat hanger wire and hold it down while adjusting its position until one side pops up about 1 cm high, which should be enough to give you some space to work with.
5. Keep pulling out very slowly on where the pink arrow is pointing until both sides catch at simultaneously your, which should unlock the car trunk without affecting ignition switch functions like push start button and electronic locks (if equipped).
These ways will help in how to pick a car trunk lock.
You Can Check it Out to Leather Car Seats Cool
Conclusion
When it comes time to pick a car trunk lock, you want to ensure that you have the right tool for the job. By following the advice in this article on how to pick a car trunk lock, you can be sure that you are choosing the best safety for your needs. Remember always to stay safe and use caution when working with locks – whether you are picking them!
Louis Wein
Louis has always been fascinated by cars. He loves the way they look, the sound of the engine, and how they make him feel when he's driving. He is always keen to learn more about different mechanics of cars and how the engine contributes to other aspects of the car. As an automotive technician with over 10 years of experience, he knew how they worked and loved taking them apart to see how they went back together. He was especially interested in the mechanics of combustion engines and loved finding ways to make them more efficient. He loves to work on cars and help people keep their vehicles running smoothly. As a senior editor, he enjoys contributing to Diy quickly because it allows him to share his knowledge and expertise with others.
