How to Spray Windshield Wiper Fluid

When it comes to keeping your car in good condition, one of the most important things to remember is to keep the windshield wipers clean and functional. In addition to keeping them clean, you should also regularly check the fluid levels in your car’s wiper fluid reservoir. Here’s a guide on how to spray windshield wiper fluid.

How to Spray Windshield Wiper Fluid

First, make sure that you have a supply of windshield wiper fluid on hand. You can either buy it at a store or mix your own using water and vinegar. Next, open the hood of your car and locate the wiper fluid reservoir. The reservoir is typically located near the windshield wipers themselves. Keep reading to know more information!

Why it’s Important to Spray Windshield Wiper Fluid

Windshield wipers do not clean and spread water evenly, and therefore it is very hard to see the road ahead. So then, we need windshield wiper fluid to spray on the vehicle’s windshield so that we can wipe away dirt and provide a clearer vision for the driver.

Wipers work on a principle of reciprocation: back and forth, usually between five and seven times per second. The rubber squeegee is pulled across the glass to wipe away water, leaving only dirty fluid behind. The fluid’s silver content gives it a blue color so you can see where all the dirt came from.

Step by Step Process: How to Spray Windshield Wiper Fluid

Step 1: Locate the Windshield Washer Fluid Reservoir.

It should be near the front of the engine of your car. The top-end will have a flip-top cap that can easily be flipped open to reveal where you should put your windshield wiper fluid in.

Step 2: Add Windshield Wiper Fluid.

You may have to unscrew the top cap of the reservoir in order to get a clear view of where you are supposed to pour your windshield wiper fluid. After getting a good look at where it is, you have to put your windshield washer fluid, take out your bottle, and slowly pour it into the reservoir.

It may take a long time, but you have to be patient since spilling even one drop of this fluid will cause your windshield wipers to stop working properly.

Step 3: Replace the Top Cap.

After putting the required amount of windshield wiper fluid in the container, close the top cap tight to make sure that the fluid doesn’t come out. If you notice any spots of windshield wiper fluid on your car’s paint job, wipe it off immediately since leaving it there for too long will cause permanent damage to your car’s body.

Close the Top Cap Tight

Step 4: Listen to See if You Can Hear the Washer Pump Running.

After putting in the windshield wiper fluid and closing the top cap, go back to your car and turn it on. Look at your windshield washer fluid reservoir to see if you can hear the quiet sound of the pump running inside the container. If there is no noise coming from it, then that means that you didn’t add enough fluid. If there is too much noise coming from it, then that means that you put in too much.

Step 5: Make Sure the Washer Nozzle Jets Are Free.

If you can hear the washer pump running inside, that means that your windshield wiper fluid should be working. But just to make sure, get out of your car and inspect your wipers’ jets by spraying them with water. If there are no blockages in between, then you can say that your windshield wiper fluid is working perfectly.

Step 6: Test Your Windshield Wiper Fluid!

If your windshield wiper fluid is working, you are now good to go and use it whenever the weather starts getting bad. However, if it doesn’t work, double-check all of your steps before calling a professional for help.

Some Tips and Suggestions

1. This is not the most accurate method, but using a paper funnel seems to work best.

2. You can’t use all of this fluid at once, so don’t buy too much!

3. Do not mix ammonia with bleach (the fumes are toxic), and do not mix blue Windex with vinegar (this will cause an acid reaction).

4. Keep windshield wiper fluid in a safe place, away from children and pets.

Keep Windshield Wiper Fluid in a Safe Place

5. Do not use an old windshield washer fluid that may have already been used to clean your car’s headlights!

6. Do not drink this! It is poisonous, and it’s no fun to get sick from drinking windshield wiper fluid.

How Do You Use a Spray Bottle to Apply Windshield Wiper Fluid

Fill the spray bottle with windshield wiper fluid. You can buy this in small, inexpensive containers at an auto parts store or large refill buckets from your local car wash. Alternatively, you can transfer some of your vehicle’s wiper fluid to a smaller container if it’s not too dirty for reuse.

Make sure the cap is on the spray bottle. Sudden temperature changes can cause pressure, which may cause it to explode. Set the nozzle of the spray bottle to mist. This will allow you to coat your windshield with wiper fluid without drenching it lightly. Spray a light mist of windshield wiper fluid onto your windshield. This will make it easier for your wipers to clean the windshield.

Does My Car Need Any Other Additives Besides This Type of Product for Better Performance

Because this product is meant to be used as a regular replacement for your car’s wipers, it does not come with any other additives. However, you can choose to purchase a windshield wiper fluid with additional elements added to the solution that will further help your visibility while driving during a winter storm or rainstorm.

In addition, these products usually come with some additive like a deicer, which is perfect for those cold winter months!

Another great product to use during the winter months is a washer fluid made primarily with water. This will effectively melt any ice on your windshield without worrying about an increased risk of skidding or sliding off the road.

Washer Fluid Use During the Winter MonthsWasher Fluid Use During the Winter Months


Windshield wiper fluid is an important part of keeping your car clean and functioning during the winter. In this post, we have discussed how to spray windshield wiper fluid so that you can keep your vehicle in good condition. The first step is to open up the hood of your car.

Once you have done that, locate the windshield washer fluid reservoir and unscrew the cap. Once you have opened the cap, please fill the reservoir with windshield washer fluid until complete. Be sure not to overfill it, or else liquid may spill out onto your engine when you close it again. We hope you found this blog post informative! If you have any other questions, feel free to reach out.

Louis Wein

Louis Wein

Louis has always been fascinated by cars. He loves the way they look, the sound of the engine, and how they make him feel when he's driving. He is always keen to learn more about different mechanics of cars and how the engine contributes to other aspects of the car. As an automotive technician with over 10 years of experience, he knew how they worked and loved taking them apart to see how they went back together. He was especially interested in the mechanics of combustion engines and loved finding ways to make them more efficient. He loves to work on cars and help people keep their vehicles running smoothly. As a senior editor, he enjoys contributing to Diy quickly because it allows him to share his knowledge and expertise with others.

We will be happy to hear your thoughts

Leave a reply

DIY Quickly